Welcome to akYtec!
 
Call us now: +49 (0) 511 / 16 59 672-0
info@akytec.de

PROCESS DISPLAYS

ITP11, ITP, ITP14, ITP16, SMI2

or search frequently asked questions:

What is the lifetime and the MTBF of ITP11 process indicators?
Can you tell me how the micro calculates what digit to display? Does it round up to the next digit, or does it truncate?
What type of signal does the ITP11 support? How should I connect it?
What type of signal does the Universal Process Indicator ITP14 support? How should I connect it?
What type of signal does the Temperature Indicator ITP16 support? How should I connect it?
What software do I need to configure the SMI2? Do I need a specialized cable?
Can I directly connect the ITP11 to an analog 4-20 mA output?
Can I connect the ITP14 to an analog 4-20 mA or 0-10 V output directly?
Can I connect the Temperature Indicator ITP16 to a temperature sensor PT100 directly or should I use a 4-20 mA converter?
I have successfully connected the SMI2 to my PC several times, but this time, an error message appeared. What should I check?
Can I connect several ITP11 displays to the common analog output? How should I connect them, in series or in parallel?
Can I connect several Process Indicators ITP14 to the common analog output? How should I connect them, in series or in parallel?
Can I connect several ITP16 Temperature Displays to the common temperature sensor? How should I connect them, in series or in parallel?
Can I use the SMI2 with an Arduino board or a PLC from any company?
I have connected the ITP11 but it doesn’t switch on, what should I check?
I have connected the ITP14 but it doesn’t switch on, what should I check?
I have connected the ITP16 but it doesn’t switch on, what should I check?
Can I connect a 0-20 mA signal to an ITP11? What about a 0-10 V or a PT100 signal?
Can I connect a 0-20 mA signal to an ITP14? What about a 0-10 V or a Pt100 signal?
I have connected a sensor to the ITP16, but the temperature on the display is far from the correct one, what should I check?
Which voltage supply does the ITP11 require: 24 VDC or 230 VAC?
What voltage does the ITP14 require?
What voltage supply does the ITP16 require?
What software do I need to program the ITP11?
What software do I need to program the ITP14?
What software do I need to program the ITP16?
Should I program the display before or after the installation?
Can I switch on/off the digital output of the ITP16 depending on the signal value at its input?
How can I scale the measuring limits of the ITP11?
Can I switch on/off the output of the ITP14 depending on the signal value at its input?
If I need to show a percentage value, what should the measuring limits be?
How can I scale the measuring limits of the ITP14?
How can I scale the measuring limits of the ITP16?
How can I set the alarm limits of the ITP11?
If I need to show a percentage value, what should the ITP16’s measuring limits be?
Can I switch on/off its the output of the ITP11 as a function of the signal value at its input?
How to change the access protection password?
What is the alarm function? How can I use it?
What is the ITP16’s input resistance?
In what colors is the display available?
What is the ITP14’s input resistance?
What conductor cross section is permitted?
What conductor cross section is permitted?
What conductor cross section is permitted?
What is the ITP16’s accuracy? What about its sample time?
What is the ITP11’s accuracy? What about the sample time?
What is the ITP14’s accuracy? What about its sample time?
Is the ITP16 protected against overload?
Is the ITP11 protected against overload currents?
Is the ITP14 protected against overload? What about reverse polarity protection?
What is the maximum permissible distance between the ITP11 and the signal source?
Is there any galvanic isolation between the input, the output, and the voltage supply circuit?
What is the maximum distance to connect an RTD or a TC signal to the ITP16?
What diameter should the mounting cutout be to install this display?
What is the maximum distance to connect a 4-20 mA signal to the ITP14?
Do you have an ePLAN 3D model of this display?
Can I set di.Low=0 and di.High=25 so that if input voltage of 0V corresponds to 0 and 10V corresponds to 25 ?
Is it possible to apply the lower measuring limit to the highest process value and the upper limit to the lowest process value?
Back to All Topics